Description

E814CP Co-Polymer Flat Roof Coating | 11 Color | Flexible | Waterproof E814CP Co-Polymer Liquid Rubber Roof Coating E814CP is a one part elastomeric co-polymer (SEBS Based) liquid rubber coating modified for excellent 500%+ elongation, tensile strength, UV resistance and exceptional weathering characteristics. This extremely flexible roof membrane has excellent waterproofing performance and resistance to ozone as well as low temperature flexibility. E814CP works on flat roofs and slightly sloped roofs that may be subject to periodic ponded or pooled water. The E814CP is Class A Fire Rated, UL Tested and Certified. The E814CP works on a wide range of roof surfaces including EPDM, APP, TPO, Hypalon, BUR, Fiberglass, PVC, Polyurethane Foam, concrete, wood and metal. Not recommended for application over tar based or bitumen roofing. For roof projects requiring a non-slip walkway as part of the roof coating system, see our E814R Co-Polymer Liquid Rubber Roof Walkway Coating . E814CP is available in 11 different colors. Comes in 1 gallon, 2.5 gallon, 5 gallon and 50 gallon drums (ships LTL freight only). Custom colors available on special order and require 30 gallon +/- 10% order and 1-2 week lead time after color acceptance. For the energy saving, solar reflective version of the E814CP, please see E814RCP Co-Polymer White Reflective Roof Coating Coverage rate depends on surface conditions and application procedures. Normally, 1 gallon per 100 square feet of a base coat and 1 gallon per 100 square feet of a topcoat combine to achieve the recommended 32 mils wet thickness (16 mils each coat). PRIMER: None required. TOPCOAT : None required Where is E814CP Co-Polymer Roof Coating U sed? Where a waterproof, extremely tough roof coating is needed. Flat & Sloped roofs Most roof surfaces including EPDM, APP, TPO, Hypalon, BUR, Fiberglass, PVC, Polyurethane Foam, Concrete, Wood, Metal surfaces Why E814CP Roof Coating? Exceptionally tough, SEBS Based waterproof 1 part roof coating Excellent adhesion to EPDM, APP, TPO, Hypalon, BUR, Fiberglass, PVC, Polyurethane Foam, Concrete, Wood, Metal surfaces Great for both Flat & Sloped Roofs Excellent waterproof with E96 Vapor Transmission Class I 0.025 perms and Water Absorption 0.04% Excellent weathering Excellent UV stability Good resistance to dirt pickup Excellent low temp flexibility 500%+ Elongation Resists mildew and fungi growth Good resistance to Alkalis and acids Available in 11 colors Underwriters Laboratories (UL) Tested & Certified Class A Fire Rated SPECIFICATIONS UNDERWRITERS LABORATORIES, INC., TESTED AND CERTIFIED FOR CLASS A U.L. CERTIFICATION TESTING DATA AVAILABLE UPON REQUEST Solids (weight) 60% Solids (volume) 52% Colors 11 colors Recommended Film Thickness 16 mils wet per coat x 2 coats = 32 mils wet Coverage Rate Depends on surface conditions and application conditions, normally 1 gallon per 100 sq' per coat x 2 coats Packaging 1 gallon, 2.5 gallons, 5 gallons, 50 gallon drum Shelf Life 12 months in unopened container VOC 349 g/L. DOES NOT MEET REGIONAL EPA VOC REGULATIONS & NOT FOR SALE IN CA, IL, IN, OH, KY, VA, MD, DE, PA, NJ, NY, CT, RI, MA, NH, ME, UT Maricopa County, AZ Flash point 105°F ASTM D3278 seta flash closed cup apparatus Heat stability 10 days at 120°F then re-evaluated: Material stability maintained Particle Size <38 microns or hegman 4-5 ASTM 1218 Density Mean=9.85#/gallon ASTM D1475 U.S. standard weight per gallon cup at 75°F and 50% R.H Viscosity @75°F, 50% R.H 5,000-10,000 (142 krebs typical)BROOKFIELD VISCOMETER (krebs stormer) Hardness 50-60 ASTM D2240 shore A @75°F 50% R.H. Barcol hardness tester model 3061 Accelerated Weathering Excellent with no apparent degradation ASTM G53 (1000 hours QUV accelerated weather tester UV-B lamps no. QES-40/280-315 nanometers. (12 hr. QUV @ 60°C and 12 hr. con @ 50°C) Tensile Strength 1000 psi ASTM D412 @ 75°F and 50% R.H. Test is result of medium value(for 3) Elongation 500% minimum ASTM D412 @ 75°F and 50% R.H Water Absorption 0.04% Vapor Transmission 0.025 perms ASTM E96 Cure time 24-48 hours @70% R.H./70°F COVERAGE RATE Coverage Rate Depends On Surface Conditions And Application Conditions, Normally 1 Gallon Per 100 Sq’ Per Coat X 2 Coats MIXING AND APPLICATION INSTRUCTIONS PRODUCT STORAGE : Store product in an area so as to bring the material to normal room temperature before using. Continuous storage should be between 60 and 80 degree F. Keep from freezing. SURFACE PREPARATION : Make certain that the substrate where the product is to be applied is clean, sound and free of all laitance, dirt, dust, oil, grease, water, dew or foreign contaminants. Power washing will be an effective preparation method for most substrates. Wire brush or abrasive blast all loose and scaling rust from metal surfaces. When topcoating EPDM or seamed roofs, make sure all seams are secure. Precautions should be exercised when coating surfaces with insulation boards such as EPS to determine that the coating will not affect the underlying insulation. When the type of insulation board is unknown, a suitable test patch can be applied to determine suitability. Surface must be dry before application. ENVIRONMENTAL CONDITIONS: Do not apply material when temperature is below 40°F during the application time or drying period. Apply material when RH is below 90% for best results. Allow for adequate dry times between coats and before inclement weather or rain. Higher humidity or lower temperatures will slow the dry time. 4) APPLICATION: This product may be applied by roller, brush, or spray. Spray applications may require masking and possible erection of wind screens to prevent over-spray damage to surrounding structures, vehicles, and other property. Be sure to apply this product at the specified coverage rate or recommended mil thickness. For larger flat roof areas, when spraying is not practical, the product can be applied with a suitable serrated squeegee and then backrolled with a 3/8” nap roller tool. Too thick of an application may result in solvent entrapment or rumpling of substrates such as EPDM. Some adhesives on existing structures (used to bond the rubber sheets to the deck/structures) may degrade, or are of a poor quality and may not re-bond when the swelling has recovered. Should this occur, you may need to re-bond the sheet rubber with quality adhesives. As we have no control over the type of adhesives used on existing structures, we cannot be held responsible for such occurrences. Apply one gallon per 100 square feet per coat (two coats recommended). Always check the previous coat for foreign contamination before recoating. First coat must be free from water and dry before second coat application. NOTE: If applying over porous substrates, such as concrete but not limited to only concrete, always apply a test patch to determine suitability concerning out-gassing, which could result in pin-holing in both the first coat and subsequent coats as well as potential blisters from the out-gassing . For best mixing results and proper blending recommend a Jiffy Mixer style drill mixer. REOPEN SERVICE TIME: Take notice of the full cure time and do not open the area to abusive use before the full characteristics of the coating is achieved. Apply when weather permits 24 hours of rain free curing. 6) MAINTENANCE : Provide for routine maintenance of your roof to assure years of trouble free performance. Ponded water areas without positive flow of debris to drain where the debris is left to build up and accumulate and cycle through drying cycles can eventually cause the debris to bond to the coating and restrict the natural elongation of the coating. This can cause delaminations and tearing over substrates by preventing the coating from moving (expansion and contraction) with the substrate it is applied over. Accordingly, remove debris or flush the debris to drain as routine maintenance before it can build up and affect the coating. LIMITATIONS Allow material to cure (24 hours) before exposure to rain or dew. Do not apply a second coat until the first coat is dry. Close all sources of air intake from roof into building to prevent solvent odor transfer into building. Do not use indoors. Product cures from solvent evaporation- Do not apply thicker than recommended. Too thick of an application can effect insulation boards such as EPS. Read the MSDS before using this product. Product is not resistant to solvent exposure. Too thick of an application can effect insulation boards such as EPS. Physical properties are typical values and not specifications. NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM. Color Size Price Tile Red 1 Gallon $ 81.65 Skry Gray 1 Gallon $ 81.65 Shadow Gray 1 Gallon $ 81.65 Safety Yellow 1 Gallon $ 126.50 Light Tan 1 Gallon $ 81.65 Dark Green 1 Gallon $ 81.65 Dark Blue 1 Gallon $ 81.65 Blue 1 Gallon $ 81.65 Brown 1 Gallon $ 81.65 Black 1 Gallon $ 81.65 Biege 1 Gallon $ 81.65 Dark Green 2.5 Gallons $ 212.75 Dark Blue 50 Gallon $ 3,148.70 Dark Green 5 Gallon $ 394.45 Dark Blue 5 Gallon $ 394.45 Dark Green 50 Gallon $ 3,148.70 Dark Blue 2.5 Gallons $ 212.75 Light Tan 2.5 Gallons $ 212.75 Brown 50 Gallon $ 3,148.70 Light Tan 5 Gallon $ 394.45 Brown 5 Gallon $ 394.45 Light Tan 50 Gallon $ 3,148.70 Brown 2.5 Gallons $ 212.75 Safety Yellow 2.5 Gallons $ 265.65 Blue 50 Gallon $ 3,148.70 Safety Yellow 5 Gallon $ 493.35 Blue 5 Gallon $ 394.45 Safety Yellow 50 Gallon $ 4,059.50 Blue 2.5 Gallons $ 212.75 Shadow Gray 2.5 Gallons $ 212.75 Black 50 Gallon $ 3,148.70 Shadow Gray 5 Gallon $ 394.45 Black 5 Gallon $ 394.45 Shadow Gray 50 Gallon $ 3,148.70 Black 2.5 Gallons $ 212.75 Skry Gray 2.5 Gallons $ 212.75 Biege 50 Gallon $ 3,148.70 Skry Gray 5 Gallon $ 394.45 Biege 5 Gallon $ 394.45 Skry Gray 50 Gallon $ 3,148.70 Biege 2.5 Gallons $ 212.75 Tile Red 2.5 Gallons $ 212.75 Tile Red 5 Gallon $ 394.45 Tile Red 50 Gallon $ 3,148.70 Shipping Shipping cost: No cost shipping lower 48 US States FedEx Ground Delivery time: Typically 3-5 days to process order plus 1 to 5 days transit time after shipment depending on location Payment We accept the following payment methods: PayPal payment due at time of order placement Please contact us if you have any questions. Service PLEASE CONTACT CUSTOMER SERVICE FOR QUESTIONS